ISSUE 12: YODA, THE MINIMED™ 670G CAMPAIGN, ACHIEVES STRONG RESULTS

Welcome to the AIM High Newsletter

You’ll find that it is filled with inspiring and educational information, best practices, important updates related to the AIM Product Portfolio and the latest news.

NEW DIABETES TECH CHANGING LIVES:
MDI PATIENTS ACHIEVING EXCELLENT TIME IN RANGE

YODA CAMPAIGN
STRONG RESULTS 2 MONTHS AFTER LAUNCH

Yoda campaign was created to drive MDI to SAP conversion on patient side. It is now active in 6 EMEA markets, 5 more will launch YODA in Q3.

Only ~2 months since launch, Netherlands, Sweden and UK achieved very strong results in terms of leads generation, with +50% of leads coming from MDI users, in line with campaign objectives.

BEST PERFORMING ADS
IN SOCIAL MEDIA

INFUSION SETS
P-CAP CONVERSION TO SC1

The conversion of P-Cap infusion sets to SC1 has already started with the launch of Sure-T family in Wave I countries.

A smooth transition was achieved thanks to your effort and great preparation!

In line with our launch plan, next wave is scheduled for January and it will involve most of the CFNs in our portfolio. In order to avoid any supply interruptions as well as any delays, feel free to highlight potential risks or local specific requirements.

For more information please contact SC1 team.

GUARDIAN SENSOR 3
TIPS & TRICKS

CALIBRATION SCHEDULE

Calibrations are due:

  • After sensor warm-up when Calibrate now is received
  • Between 40 minutes and 2 hours
  • Within 6 hours on the first day
  • Every 12 hours
  • When the system detects a calibration is needed for optimal performance, this is called a diagnostic calibration
  • More likely to occur day 1, but can also occur on days 2-7 for continued sensor accuracy
  • Calibrate 3-4 times spread throughout day including bedtime
  • Best time to calibrate is before meal and before bedtime
  • Do not calibrate when sensor or blood glucose values are changing rapidly, e.g. following meals or physical exercise


Calibration Reminder

  • User might forget to calibrate when the alert comes too early before the calibration is needed (rather put 10-20 min vs. 1 hour)


“Calibration not accepted” alert

  • Wait at least 15 minutes before the next calibration
  • User will be directed to change sensor if the 2nd calibration is not accepted

INSERTION TECHNIQUE & TAPING

  • Wash your hands with soap and water
  • Clean the selected site with an alcohol swab and allow the alcohol to dry. Do NOT use IV prep or the sensor may not work properly.
  • Do NOT use skin-preparation solutions prior to insertion e.g. Cavilon™
  • Local anesthetic creams (EMLA is ok, check with your local Medtronic team on other products)
  • Do NOT insert the sensor through tape or dressing
  • Insert the sensor according to the instruction in the IFU
  • Ensure that the sensor is securely taped

INSERTION SITES

For best sensor glucose performance avoid

  • where clothing may rub or constrict (for example, the beltline)
  • where the body naturally bends a great deal, which may cause the sensor to pull out
  • sites that are scarred or have hardened tissue or stretch marks


Guardian™ Sensor 3 is approved for the abdominal area and the arm*

  • Prefer insertion in the back of the arm*


The sensor insertion site should be at least

  • 5 cm (2 inches) from the navel
  • 2.5 cm (1 inch) from any manual insulin injection site 2.5 cm (1 inch) from the insulin pump infusion site

Rotate sensor insertion sites


Avoid sites in close proximity to the navel, insulin infusion site or any manual infusion sites


* Assistance may be needed for sensor insertion into the back of the upper arm. Some users found it difficult to insert the sensor into the arm by themselves.

GOT ANY TOPICS FOR THE NEXT ISSUE?

CLICK HERE

© 2019 Medtronic